 |
 |
 |
 |
 |
 |
| MODEL SELECTION |
To select a Gate Buster model, consider the following.
| ・Applicable Models | ・Model Section Guide | ・Breaking Power |
| ● APPLICABLE MODELS |
| Layout | Tool | STRUCTURE PLAN |
|||||
| Type | Breaking Power(t) | ||||||
| 5.5 | 9 | 14 | 27 | 40 | |||
| Waist Level | Standard | GB-MN | GB-DM | GB-5VS | No.1 | ||
| Flexible | GB-DF | GB-5FK | GB-10S | No.2 | |||
| Floor Level | GB-10F | GB-20F | No.3 | ||||
| Standard | GB-5LV | GB-10M | GB-20 | No.4 | |||
| 1) | STRUCTURE PLAN | ： | For an overview, see STRUCTURE PLAN (PDF*)No.1，No.2，No.3， and No.4. |
* |
To view the STRUCTURE PLAN, you need Adobe Reader installed. If you do not have Adobe Reader installed, please download it by Left Button (free of charge). |
| ● MODEL SECTION GUIDE |
| In model selection, narrow it down to the most suitable model while considering the following conditions. |
| 1. | Casting Material | ： | (Tensile strength ㎏/㎜²) | ||||
| 2. | Sectional Area of Gate | ： | ㎜× | ㎜ | |||
| 3. | Weight | ： | Weight in isolation | ㎏/piece | |||
| 4. | Uses | ： | ①Separating Gate | ②Separating Runner | ③Separating Side Riser | ④Separating Top Riser | |
| 5. | Molding Machine | ： | |||||
| 6. | Frequency of use | ： | ①8 Hours/Day | ②16 Hours/Day | ③Other | ||
| 7. | Layout | ： | ①Floor Level Line | ②Waist Level Line | |||
| 8. | Operation | ： | ①Before shot | ②After shot | |||
| 9. | Voltage | ： | V | Hz | |||
| ● BREAKING POWER |
| The Gate Buster's breaking power varies greatly with the conditions specified in the casting plan and other plans. For Material FCD-450, refer to the following guide. |
| Model | Breaking Power Ton |
Maximum Breakable Sectional Area ㎜² (㎜×㎜) |
| GB-MN | 5.5 | 100 (10×10) |
| GB-DM(DF) | 9 | 200 (15×15) |
| GB-5LV(5VS,5FK) | 14 | 440 (21×21) |
| GB-10M(10F,10S) | 27 | 1,100 (33×33) |
| GB-20(20F) | 40 | 3,000 (55×55) |
| For gate separation with the Gate Buster, it is extremely important to use the following effectively | |
| 1)Distance between the bill and breaking point. | |
| 2)Separator notch. | |
| To separate work of Material FCD-450 with a GB-10M, for example, the breaking power with tensile strength alone will be | |
| 1,100㎜²×45㎏/㎜²＝49,500㎏<49.5ton> | |
| Even if the friction coefficient is excluded, the GB-10M with a breaking power of 27 ton cannot complete the separation. The key point in this case is therefore to make effective use of 1) and 2). | |
| <NOTE> | If there are two or more gates, be sure to begin with the edge of side A in the separation, then process the remaining gates in order. |
| 1) | CASTING PLAN | ： | For an overview, see CASTING PLAN(PDF*). |
| * |
To view the CASTING PLAN, you need Adobe Reader installed. If you do not have Adobe Reader installed, please download it by Left Button (free of charge). |
